Point System. Adjust the saddle forward or backward to the proper position and tighten the saddle lock down screw. All lbanez guitars use A for a standard pitch.
Tighten the Stud lock screw 3. Occasionally, there are times when the neck may need adjustment. Loosen the pressure pad lock screws on the top lock with a 3mm allen wrench. If the 12th fret harmonic is higher than the fretted s20ex, the saddle needs to be moved forward. Ssx the string around the tuning machine and tune to pitch 6. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips. Height adjustment is made by adjusting the 2mm allen screws on either side of the bridge.
Tune the guitar to pitch and recheck the intonation. Solid Body Electric Guitars. When the guitar is properly adjusted, tighten the top lock pressure pad screws 5. Different gauges of strings can result in the need for truss rod, tremolo, action or intonation adjustment.
The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on either side of the tremolo unit. If the intonation is still not correct repeat steps 1, 2 and 3. Retune the guitar to the proper pitch and check the angle. For ease in retuning, it is recommended ibanz one string at a time be changed and tuned. Raise or lower the tremolo to the desired string height using a 4mm allen wrench.
Only loosen the screw enough to move the saddle. The purpose of this is to accommodate for different tunings or different gauges of strings. Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the String holder block. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read the same on the tuner.
The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on manua side of the tremolo unit. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. Insert the mamual arm into the arm socket and turn the Arm torque adjustment nut A clockwise until it stops. Make sure the truss rod is properly adjusted before adjusting the action. On the bass plate there are two holes for each saddle lock down screw.
To check the intonation: Using a Phillips head screw driver, turn the Spring tension adjustment screw and adjust the length of the spring. Over adjustment can result in damage to the instrument and will no be covered under warranty.
If the intonation is still not correct repeat steps 1, 2 and 3. Cut off the ball end of the new s20ex above the string winding and insert the end of the string in between the main saddle and the Amnual holder block.
To adjust the string height of the saddles use a 1. Height adjustment is made by adjusting the 2mm allen screws on either side of the bridge.
When the guitar is properly adjusted, tighten the top lock pressure pad screws. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration. Remove the tremolo cavity cover plate from the back of the body. All guitar necks are subject to great stress as a result of string tension, humidity or changes in climactic conditions.
Loosen the heigth adjustment screw 5 ibahez both sides of the bridge using a 2 Phillips. To check the intonation: Loosen the heigth adjustment screw 5 on both sides of the bridge using ihanez 2 Phillips 2. On the bass plate there are two holes for each saddle lock down screw. Loosen the pressure pad screws on the top lock with a 3mm allen wrench and loosen the string to be adjusted.
Adjust the saddle forward or backward to the proper position and tighten the saddle lock down screw. Only loosen the screw enough to move the saddle. Tighten the String stopper Screw. Adjusting the String Height. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips. The rotation torque of the arm can be adjusted by changing the number of bushings on the arm.
For ease in retuning, it is recommended that one string at a time be changed and tuned. Use an electronic tuner and tune the guitar to a standard pitch. Both bushings should be completely hidden. Occasionally, there are times when the neck may need adjustment.
0コメント